Type: Driver
File Name:
File Size: 30.7 MB
58 (3.68)
Downloads: 43
Supported systems: Windows Vista, Windows Vista 64-bit, Windows XP 64-bit, Mac OS X, Mac OS X 10.4, Mac OS X 10.5
Price: Free* (*Free Registration Required)

Download Now

Windows is a registered trademark of Microsoft Corporation. This document contains proprietary information of Continental Access. Unauthorized reproduction of any portion of this manual without the written authorization of Continental Access is prohibited. The information in this manual is for informational purposes only. It is subject to change without Lantronix DeviceInstaller.

Scripting must be enabled to use this site.

Companies, names and data used in examples herein are fictitious unless otherwise noted. Continental assumes no responsibility for incorrect information this manual may contain. The Xport plugs directly into Continental Lantronix DeviceInstaller controllers.

The Xport for Super2 controllers and accelerator boards are referred to as a network interface board. This information must be supplied to you by the Lantronix DeviceInstaller administrator. If this address changes in the future, the CardAccess software will not communicate to the panel. Lantronix DeviceInstaller is highly recommended to use a static IP address.


This cable can be used to program the Lantronix using hyperterminal. Lantronix DeviceInstaller hyperterminal is an alternate method to using DeviceInstaller. Using a crossover cable eliminates any switches or hubs from blocking the device.

  • Elabo GmbH - Driver download
  • Latest version of DeviceInstaller
  • Lantronix device installer download
  • Lantronix device installer 4.2
  • Welcome to the Schneider Electric Website

It is not recommended to cut the serial cable supplied with the external Lantronix device. This serial cable is for configuring the Lantronix device only.

Java - How to get Lantronix XPort IP address programmatically - Stack Overflow

The gauge of the wire doesn t meet the Continental Access wiring specifications. Below is the wiring diagram for the Lantronix cable. Lantronix 25 pin Panel polling connector txd Lantronix DeviceInstaller gnd 2 5 Scope This document contains information regarding the installation and the configuration of the Lantronix Lantronix DeviceInstaller. DeviceInstaller is an all-in-one utility that gives you the ability to configure a Lantronix device using different methods. The two methods are telnet and web. This document will focus on using the telnet method.

Where can I download the Lantronix DeviceInstaller for W7, W8, or W10?

Using the telnet feature of DeviceInstaller is Lantronix DeviceInstaller similar to using hyperterminal and a serial cable on external Lantronix devices. In addition to this document, you may refer to the DeviceInstaller user guide on the Lantronix website. The following information might be slightly different compared to the website.

Lantronix DeviceInstaller download, you will be prompted to download via ftp or http. Download the utility to your hard drive. The version you download should be or Lantronix DeviceInstaller. Installing DeviceInstaller Once the DeviceInstaller is downloaded to your hard drive, you must install it. Double click the file you downloaded and follow the prompts to install. The program will install a shortcut in the start menu under Lantronix.

Verify the Lantronix DeviceInstaller program opens refer to figure 1. If you are prompted to check for updates on the product information base, click NO.

Where can I download the Lantronix DeviceInstaller for W7, W8, or W10?

DeviceInstaller will display all Lantronix devices detected on the network. Devices that do not Lantronix DeviceInstaller an IP address assigned or are configured on a different network, display in red. You must assign an IP address to the device to use it. If DeviceInstaller fails to detect your Lantronix device, refer to Appendix B for troubleshooting tips. Click and expand Local Area Connection.


UDS and XPort should display. Verify the device you are configuring displays on the right side of the screen.

You can identify your Lantronix DeviceInstaller by the hardware address. The hardware address is also called the MAC address. All network devices have a unique MAC address.

XPorts have the MAC address written on the outside. If this occurs, the IP address assigned from the DHCP server along with the hardware address will display on the right side of the screen. If the current IP address is incorrect, you can manually assign the correct IP address. After verifying the hardware address, click the correct Lantronix device on the right side of the screen. The device will highlight refer to figure 2. The Lantronix DeviceInstaller is a Windows-based GUI application that provides an easy way to install and configure specific Lantronix device server products. Lantronix Device Installer Software Firmware Lantronix DeviceInstaller. Lantronix Device Installer. Version: Date:4/23/

Other Drivers