DRIVER FOR AOPEN AK76F-N SIS USB 2.0
AOPEN AK76F-N SIS USB 2.0 DRIVER DETAILS:
|File Size:||29.1 MB|
|Supported systems:||Windows 10, 8.1, 8, 7, 2008, Vista, 2003, XP|
|Price:||Free* (*Free Registration Required)|
AOPEN AK76F-N SIS USB 2.0 DRIVER
Overclocking refers to running a component at a speed greater than it was designed for. This gives enhanced performance but often at the expense of decreased stability.
This site maintains listings of network drivers available on the web, organized by company. Includes links to useful resources. PC maintenance article - It s a brush based fan, which means it makes noise -particularly when it s cold at bootup. Some also want to replace it to get better cooling. The most common way of doing this for most chipsets is to use a AOpen AK76F-N SiS USB 2.0 Orb chipset cooler. To start the mod, I removed the old fan.
You have to be careful when taking it off, because the back of the board has a lot of leads which can be scratched easily. Just use a needle nose pliers to clamp the plastic and push it through the hole. The fan will then AOpen AK76F-N SiS USB 2.0 with ease. Be careful not to scratch the leads on the back of the board I was surprised to find that Abit actually used thermal compound although a very small amount between the chipset fan and the Northbridge.
I didn t think there would be any kind of material there at all. Not much thermal compound Then I attached the Blue Orb. I soon found out that the Blue Orb does not fit on the KT7. Because of this, the Blue Orb is short by about half a centimeter. I tried bending it and forcing it on the board for about thirty minutes to no avail.
There is simply no possible way to get it to fit. Of course you can juse use thermal tape on the bottom without clamping the unit down, but this defeats the purpose of getting the added cooling of the Blorb. I then tried to mount the Blue Orb s fan on the KT7 s heatsink, since it was obvious the Blorb s fan was a tad better. This also was impossible to accomplish without some serious modification. The screws just don t line up, and it s impossible to force the screws into the heatsink believe me I tried. Mounting the fan on the KT7 s heatsink won t work It is a good idea to take off the current heatsink and fan on the KT7 s Northbridge. Abit didn t use very much thermal paste at all. It AOpen AK76F-N SiS USB 2.0 a good idea to take it off and put a new thin AOpen AK76F-N SiS USB 2.0 of paste over the chip. It s possible this could further increase stability of the board, possibly allowing you to raise the FSB higher.
Since users have asked exactly how to remove the BIOS chip from the board, I have put together a short little guide.
The BIOS chip is located on the bottom left of the board. The writing on the chip not the sticker reads from the LEFT corner of the board - remember this when you put it back in. The chip is in it s socket rather securely.
It s not possible to just lift the chip out with your fingers. You will need to use a flathead screwdriver to pry the chip off.
Support and driver downloads for modems, motherboards, printers, audio, video, LAN, USB, , etc
If you get a lot of resistance, chances are you are trying to pry the BIOS chip s socket off the motherboard, and not the BIOS chip out of it s socket. The chip will pop right out.
Be careful when prying because if you pry a little too far the end pins will start to bend. Model, AK76F-N. CPU: Socket A SIS Main Memory: DDR [PC] DIMM: DDR DIMM DIMM Type: 64///MB & 1GB USB Port x 1 USB Port Game Connector Chassis Intrusion Connector: Case Open Connector.
KB. Fixed the USB device can't be detect after s3 resume. Driver, SiS AGP Driver, Re, 6/4/, KB USB Driver, R, 9/1/